Aluminum alloys
Label
Aluminum alloys
Name
Aluminum alloys
Source
nasat
Focus
Actions
Incoming Resources
- The compressive yield strength of extruded shapes of 24ST aluminum alloy, by R.L. Templin, F.M. Howell, and E.C. Hartmann
- Carbon nanotube aluminum matrix composites, Brent J. Carey, Jerome T. Tzeng, and Shashi Karna
- Experimental study of torsional column failure, by Alfred S. Niles
- Corrosion embrittlement of duralumin, by Henry S. Rawdon, II
- Mechanical properties of aluminum-alloy rivets, by William C. Brueggemann
- Effect of alternately high and low repeated stresses upon the fatigue strength of 25ST aluminum alloy, by G.W. Stickley
- Fatigue testing of wing beams by the resonance method, by William M. Bleakney
- An investigation of the effectiveness of stiffeners on shear-resistant plate-girder webs, by R.L. Moore
- Fracture toughness of SiC/Al metal matrix composite, Yury Flom, B.H. Parker, H.P. Chu
- Moisture-induced alumina scale spallation, the hydrogen factor, James L. Smialek
- On the determination of the origin of linear anomaly in the macrostructure of VPPA welded 2219-T87 aluminum alloy, preliminary report, by W. A. Jemian
- Wear of aluminum and hypoeutectic aluminum-silicon alloys in boundary-lubricated pin-on-disk sliding, John Ferrante and William A. Brainard
- "ALCLAD", a new corrosion resistant aluminum product, by E.H. Dix, Jr
- Characterization of residual stress effects on fatigue crack growth of a friction stir welded aluminum alloy, John A. New [and seven others]
- Effects of range of stress and of special notches on fatigue properties of aluminum alloys suitable for airplane propellers, by Thomas J. Dolan
- Compression tests of some 17S-T aluminum-alloy specimens of I cross section, by H.N. Hill
- Spin forming aluminum crew module (CM) metallic aft pressure vessel bulkhead (APVBH), phase II, Eric K. Hoffman [and six others]
- Techno-economic analysis for shear assisted processing and extrusion (ShAPE) of high-strength aluminum alloys, Sertȧ Akar, Christopher Kinchin, and Parthiv Kurup
- Summary of results of tests made by aluminum research laboratories of spot-welded joints and structural elements, by E.C. Hartmann and G.W. Stickley
- Outdoor exposure results for pretreated and topcoated aluminum armor alloys 2519, 5083, 7039, John V. Kelley and Brian E. Placzankis
- Three-dimensional cellular structures enhanced by shape memory alloys, Michael V. Nathal [and four others]
- Design, optimization, and evaluation of A1-2139 compression panel with integral T-stiffeners, Sameer B. Mulani ... [and others]
- Tensile and pack compressive tests of some sheets of aluminum alloy, 1025 carbon steel, and chromium-nickel steel, by C.S. Aitchison and James A. Miller
- Torsion test of a monocoque box, by Samuel Levy, Albert E. McPherson, and Walter Ramberg
- The compressive strength of duralumin columns of equal angle section, by Eugene E. Lundquist
- The direct-stress fatigue strength of 17S-T aluminum alloy throughout the range from 1/2 to 500,000,000 cycles of stress, by E.C. Hartmann and G.W. Stickley
- Investigation of methods for selectively reinforcing aluminum and aluminum-lithium materials, R. Keith Bird [and four others]
- Torsional stability of aluminum alloy seamless tubing, by R.L. Moore and D.A. Paul
- Data on optimum length, shear strength, and tensile strength of age-hardened 17S-T machine-countersunk rivets in 75S-T sheet, by Evan H. Schuette and Donald E. Niles
- Probabilistic analysis for comparing fatigue data based on Johnson-Weibull parameters, Brian L. Vlcek, Robert C. Hendricks and Erwin V. Zaretsky
- Corrosion embrittlement of duralumin, by Henry S. Rawdon, I
- A comparison of corrosion-resistant steel (18 percent chromium - 8 percent nickel) and aluminum alloy (24ST), by J.E. Sullivan
- Study on effects of powder and flake chemistry and morphology on the properties of Al-Cu-Mg-X-X-X powder metallurgy advanced aluminum alloys, P.J. Meschter ... [and others]
- Some comparative tests of plain and alclade 24S-T sheet, by R.L. Moore
- Bending tests of a monocoque box, by Albert E. McPherson, Walter Ramberg and Samuel Levy
- Effect of radius on bulging and fracture of through-cracked cylindrical pressure vessels at cryogenic temperatures, by Timothy L. Sullivan and William S. Pierce
- Tensile behavior of boron, Daniel J. Chwirut
- Simulation of fatigue crack initiation at corrosion pits with EDM notches, Stephen W. Smith, John A. Newman, Robert S. Piascik
- Metallurgical characterization of the fracture of several high strength aluminum alloys, M. Dilip Bhandarkar and W. Barry Lisagor
- MSFC evaluation of the space fabrication demonstration system (beam builder), by E.O. Adams and C.N. Irvine
- Variation of properties throughout cross section of two extruded shapes, by F.M. Howell
- Preliminary fatigue studies on aluminum alloy aircraft girders, by Goodyear-Zeppelin Corporation
- High temperature dispersion strengthening of NiAl, Mark Sherman and Krishna Vedula
- The growth of small corrosion fatigue cracks in alloy 7075, Robert S. Piascik
- An evaluation of the plasticity-induced crack-closure concept and measurement methods, James C. Newman, Jr
- The effect of methods of testing on the ultimate loads supported by stiffened flat sheet panels under edge compression, by Marshall Holt
- Evaluation of aluminum alloy 2050-T84 microstructure and mechanical properties at ambient and cryogenic temperatures, Robert A. Hafley ... [and others]
- Effect of rivet or bolt holes on the ultimate strength developed by 24S-T and alclad 75S-T sheet in incomplete diagonal tension, by L. Ross Levin and David H. Nelson
- Impact testing of aluminum 2024 and titanium 6A1-4V for material model development, J. Michael Pereira [and three others]
- Fatigue resistance of liquid-assisted self-repairing aluminum alloys reinforced with shape memory alloys, Shape Memory Alloy Self-Healing (SMASH) technology for aeronautical applications, M. Clara Wright, Dr. Michele Manuel, Dr. Terryl Wallace
Outgoing Resources
- Focus1