Rotors
Authority Link
(OCoLC)fst01100660
Label
Rotors
Name
Rotors
Source
fast
Focus
Actions
Incoming Resources
- Subject of44
- Technology assessment for large vertical-lift transport tiltrotors, Peter J. Germanowski, Brandon L. Stille, and Michael P. Strauss
- Oil-free shaft support system rotordynamics, past, present, and future challenges and opportunities, Christopher DellaCorte
- Eigenvalue assignment strategies in rotor systems, final report, by John N. Youngblood and Kenneth J. Welzyn
- Dynamic blade loading in the ERDA/NASA 100 kW and 200 kW wind turbines, D.A. Spera, D.C. Janetzke, T.R. Richards
- Health monitoring of a rotating disk using a combined analytical-experimental approach, Ali Abdul-Aziz ... [and others]
- Numerical study of stratified charge combustion in wave rotors, M. Razi Nalim
- The aerodynamic performance of an over-the-rotor liner with circumferential grooves on a high bypass ratio turbofan rotor, Richard F. Bozak, Christopher E. Hughes, James Buckley
- Wave engine topping cycle assessment, Gerard E. Welch
- Active noise control of low speed fan rotor-stator modes, Daniel L. Sutliff [and three others]
- Ultrasonic resonance spectroscopy of composite rims for flywheel rotors, Laura M. Harmon, George Y. Baaklini
- Nearfield unsteady pressures at cruise Mach numbers for a model scale counter-rotation open rotor, David B. Stephen
- Performance and vibratory loads data from a wind-tunnel test of a model helicopter main-rotor blade with a paddle-type tip, William T. Yeager, Jr. [and four others]
- Development and testing of tip devices for horizontal axis wind turbines, G.W. Gyatt and P.B.S. Lissaman ; prepared for National Aeronautics and Space Administration, Lewis Research Center; for U.S. Department of Energy, Conservation and Renewable Energy, Wind Energy Technology Division
- Analytical models for rotor test module, strut, and balance frame dynamics in the 40- by 80-ft wind tunnel, Wayne Johnson
- Design and integration of a rotor alone nacelle for acoustic fan testing, Tony D. Shook [and five others]
- Effects of bearing deadbands on bearing loads and rotor stability, final report
- Integration of NASA-developed lifing technology for PM alloys into DARWIN®, R. Craig McClung, Michael P. Enright, and Wuwei Liang
- Inlet acoustic data from a high bypass ratio turbofan rotor in an internal flow component test facility, Richard F. Bozak
- A comprehensive C++ controller for a magnetically supported vertical rotor, version 1.0, Carlos R. Morrison
- The effect of modified control limits on the performance of a generic commercial aircraft engine, Jeffrey T. Csank ... [and others] ; prepared for the 47th Joint Propulsion Conference and Exhibit cosponsored by AIAA, ASME, SAE, and ASEE, San Diego, California, July 31-August 3, 2011
- Magnetic levitation for long-life space mechanisms, technology assessment and remaining challenges, Samuel A. Howard and Christopher DellaCorte, Michael J. Dube
- Two-dimensional aerodynamic characteristics of the OLS/TAAT airfoil, Michael E. Watts and Jeffrey L. Cross
- Simulink® controller for a reluctance motor with four-pole rotor and 36-tooth stator, Carlos R. Morrison and Andrew J. Provenza
- Comparison of predicted low speed fan rotor/stator interaction modes to measured, Daniel L. Sutliff, James Bridges, Edmane Envia
- Validation of the predicted circumferential and radial mode sound power levels in the inlet and exhaust ducts of a fan ingesting distorted inflow, L. Danielle Koch
- Acoustic properties of a supersonic fan, by Arthur W. Goldstein, Frederick W. Glaser, and James W. Coats
- Wind-tunnel tests of a cyclogiro rotor, by John B. Wheatley and Ray Windler
- Design selection and analysis of a swept and leaned stator concept, Edmane Envia, M. Nallasamy
- Halbach magnetic rotor development, Christopher A. Gallo
- Estimation of dynamic rotor loads for the rotor systems research aircraft, methodology development and validation, R. W. Du Val and M. Bahrami
- Summary of design and blade-element performance data for 12 axial-flow pump rotor configurations, by Max J. Miller [and four others]
- Design of a tapered and twisted blade for the NREL combined experiment rotor, March 1998-March 1999, P. Giguere and M.S. Selig
- Levitation performance of two opposed permanent magnet pole-pair separated conical bearingless motors, Peter Kascak [and four others]
- Permanent magnetic bearing for spacecraft applications, Wilfredo Morales and Robert Fusaro, Albert Kascak
- Factors affecting inlet-engine compatibility during aircraft departures at high angle of attack for an F/A-18A aircraft, W.G. Steenken [and three others]
- HPOTP low-speed flexible rotor balancing- phase I final report, J. Giordano, E. Zorzi
- The effects of Reynolds number, rotor incidence angle and surface roughness on the heat transfer distribution in a large-scale turbine rotor passage, reported by M.F. Blair
- Loads and performance data from a wind-tunnel test of generic model helicopter rotor blades, William T. Yeager, Jr., and Matthew L. Wilbur
- Windage power loss in gas foil bearings and the rotor-stator clearance of high speed generators operating in high pressure environments, Robert J. Bruckner ; prepared for the ASME Turbo Expo 2009 sponsored by ASME, Orlando, Florida, June 8-12, 2009
- Performance of axial-flow fan and compressor blades designed for high loadings, by Seymour M. Bogdonoff and L. Joseph Herrig
- Probabilistic methods for structural reliability and risk, Christos C. Chamis ; prepared for the 13th European Conference on Composite Materials sponsored by the European Society for Composite Materials Stockholm, Sweden, June 2-5, 2008
- Acoustic measurements from a rotor blade-vortex interaction noise experiment in the German-Dutch wind tunnel (DNW), R.M. Martin [and three others]
- Performance, inflow, and tip loss characteristics of rotors with discontinuous steps in twist and lift at the blade-tips, Larry A. Young
- Multiscale/multifunctional probabilistic composite fatigue, Christos C. Chamis
Outgoing Resources
- Focus1